...
- Unless you know EXACTLY how to build a part (which you probably don't), assume that you'll need to build it 3 times before you get it right.
- Identify all the materials you need for a part BEFORE BEFORE you start building it. Too often, the cause of delaying a part comes down to the fact that it takes 2-3 weeks to arrive.
- Identify what you need (ask someone who's built it before if you don't know)
- Look up the delivery time. If it's not shown, assume it takes 1 week for the part to get here.
- Submit an order for it to the treasurer
Materials
It's important to have the materials you need in lab, but it can be difficult to figure out what exactly you need if you're not as experienced. To make it easier, here is a list of materials that we should generally have in lab at all times, along with the price, safety notes, and purpose of the part. Other materials, such as specific bolts, heat inserts, etc. depend on your specific application.
*Note: these links are used as a pretty good reference, but if you find links with better prices/better materials, feel free to update it!
Part Name | Description | Safety Notes | Approx. Cost before Shipping | Links |
---|---|---|---|---|
STOCK (metal, plastic, other) | ||||
Acrylic sheet | Can be lasercut. Rather brittle, so be careful when drilling/cutting (use slow speeds) | |||
Polycarbonate sheet | More flexible than acrylic. Don't laser cut it, because it can catch fire/discolor | |||
Aluminum sheet stock | ||||
80/20 bars and connectors | ||||
G10 sheet | Composite fiberglass sheet. Can't laser-cut. Can waterjet, but beware delamination | |||
Phenolic sheet | Composite insulating material. Can't laser-cut. Can waterjet, but beware delamination. Tricky to machine. | |||
3D printer filament | ||||
SAFETY MATERIALS | ||||
Nitrile gloves | Latex-free, puncture-resistant gloves. (for reference, Latex = medical use, Vinyl = for use with food and other non-hazardous substances). Make sure we have small, medium and large (we run out pretty often) | https://www.amazon.com/MedPride-Powder-Free-Nitrile-Gloves-Medium/dp/B00GS8W3T4/ref=sr_1_3?keywords=nitrile+gloves&qid=1554841699&s=gateway&sr=8-3 | ||
Dust masks | Good for filtering non-toxic particles like dust and dirt. | Use respirator if working with toxic particles. | https://www.amazon.com/9118-Disposable-Non-Toxic-Filter-cleaning/dp/B005HJ4QI6/ref=sr_1_9?keywords=dust+masks&qid=1554841789&s=gateway&sr=8-9 | |
Respirators | Get these through MIT Medical and EHS. There are different canisters depending on the application (i.e. don't use the same ones for fumes as for particulates. Consult EHS for details) | Obtained via MIT Medical and EHS. https://ehs-mit-edu.ezproxy.canberra.edu.au/site/respiratory-protection | ||
Safety goggles | Smaller ones are more comfy, larger ones for people with glasses. | If cutting certain plastics, make sure to wear goggles that cover the sides of your eyes. | We should have these in lab already. | |
TAPE | ||||
Painter's tape | Usually blue tape, sticky but can be easily removed. | https://www.amazon.com/ScotchBlue-Painters-Multi-Use-1-88-Inch-60-Yard/dp/B00004Z4DU/ref=sr_1_1_sspa?keywords=painter%27s+tape&qid=1554841956&s=gateway&sr=8-1-spons&psc=1 | ||
Duct tape | Can fix anything!! | https://www.amazon.com/Tape-King-Professional-3-Pack-Silver/dp/B078X3F29Q/ref=sr_1_1_sspa?keywords=duct+tape&qid=1554841977&s=gateway&sr=8-1-spons&psc=1 | ||
Gaffer's tape | Heavy cotton cloth pressure-sensitive tape with strong adhesive and tensile properties. Surprisingly expensive. | https://www.amazon.com/Premium-Gaffer-GafferPower-Available-Multiple/dp/B00GZE3UJ8/ref=sr_1_1_sspa?keywords=gaffer%27s+tape&qid=1554842041&s=gateway&sr=8-1-spons&psc=1 | ||
Kapton tape | Flexible tape made from polyimide film, good over wide temperature range | |||
TOOLS (for cutting, drilling, sanding, etc.) | ||||
Multimaster | Gloves, safety goggles | |||
Angle grinder | Gloves, safety goggles | |||
Dremel (and Dremel bits) | Gloves, safety goggles | |||
Drill | Gloves, safety goggles | |||
Sandpaper | The higher the grit, the finer the sandpaper. (We usually use 60-2000 grit, but there's a wide variety that you can choose depending on your application. Wet-sand when using higher grit to get rid of the particles as you're sanding. | Gloves, Safety goggles, Respirator (if working with composites) | ||
Flapper wheel | Good for sanding the inside of tubes to save time. Attaches to a drill. | Gloves, safety goggles, respirator (if working with composites) | ||
Heat gun | Good for speeding up epoxy cure times, and for other applications. | Gloves, safety goggles, respirator (if material off-gasses) | ||
EPOXY (and other bonding/filling materials). In general, cure times increase if it's colder, so keep that in mind. | ||||
West Systems epoxy - FAST hardener | Cures in 6 hours | Gloves, ventilated area | ||
West Systems epoxy - SLOW hardener | Cures in 24 hours | Gloves, ventilated area | ||
Fibreglast System 3000 epoxy | 24 hour cure time. Can oven-cure to increase strength (cure cycle listed online and on back of container) | Gloves, ventilated area/respirator | ||
Aeropoxy | Used for low-temp applications. | Gloves, ventilated area | ||
5-minute epoxy | Used to bond things that are NOT structural. Short working time, cures in 15-20 minutes. | Gloves | ||
3M Bondo | Used as a a filler for cracks/low spots, etc. Has a low melting point, so don't use it for high-temp parts. | Requires respirator, gloves | ||
Proline | Black in color, used as filler. Real messy. | Gloves | ||
COMPOSITES | ||||
E-glass | Used for electrical properties (hence the "E"). Can't be laser-cut. (This applies to fiberglass in general) | Gloves (causes splinters) | ||
S-glass | Stronger than E-glass ("S" for structural) Can't be laser cut. (This applies to fiberglass in general) | Gloves (causes splinters) | ||
Carbon fiber | Not radio-frequency (RF) transparent. Can be laser-cut if dry (no epoxy applied) | Gloves (causes splinters) | ||
LAYUP SUPPLIES | ||||
Squeegees | ||||
Super77 spray glue | ||||
Wax paper | ||||
Popsicle sticks | ||||
Disposable squeegees | ||||
Foam rollers | ||||
Silver Sharpies | ||||
Epoxy mixing boats | ||||
VACUUM BAGGING SUPPLIES | ||||
High-temp vacuum bag | ||||
Low-temp vacuum bag | ||||
Vacuum tape | ||||
Release film | ||||
Bleeder fabric | ||||
Peel ply | ||||
MOLD-MAKING | ||||
MDF (medium-density fiberboard) | Easy to machine, durable. Good choice for making molds, but you can also use foam if ya want. | |||
Mold release wax | Applied to mold to aid in mold release. Apply 3-5 layers, letting set for 15 minutes in between coats. Can choose Meguiar's (first link) or Partall (second link), but it looks like Partall is cheaper. | Gloves | $24.95/11-oz tin $12.25/24-oz tin | https://www.amazon.com/Fibre-Glast-Meguiars-Conditioner-Release/dp/B015NM4QCW https://www.fibreglast.com/product/Parting_wax_1016/Mold_Releases |
PVA film | Applied in a thin layer, helps with mold release. Dries in 20 minutes, can be wiped away with warm water after part released from mold. | Gloves | $10.75/quart | https://www.fibreglast.com/product/PVA_Release_Film_13/Mold_Releases |
Gel coat | Used as a finish for molds. Don't apply too thick of a layer or it'll come off with the part. | Requires respirator | $46.95/quart | https://www.fibreglast.com/product/white-gel-coat-682/Gel-Coating-Supplies |
SOLVENTS | ||||
Acetone | Dissolves liquid epoxy. Very volatile (keep container closed or it'll evaporate away) | Gloves | ||
Isopropyl alcohol (IPA) | Gloves | |||
Ethanol | Gloves | |||
POWDERS | ||||
Colloidal silica | Essentially powdered fiberglass. Can be mixed with epoxy to thicken (acts as filler/adds strength) | Requires respirator | ||
Cabosil (fumed silica) | Powdered fiberglass. Can be mixed with epoxy to act as a filler | Requires respirator | ||
Phenolic microballoons | Phenolic in dust form. Can be mixed with epoxy to form an ablative mixture. | Requires respirator |
Machining/Building Things
Lasercutting:
Mill:
Lathe:
Bandsaw:
HAAS:
Router:
3D Printer:
Layups:
...